1. What Is S550GD?
S550GD is a structural steel grade in EN 10346 - continuously hot-dip coated steel flat products for cold forming. The "550" is the guaranteed minimum yield strength in MPa (Rp0.2); the "GD" stands for low-temperature-forming structural steel. It sits at the top of the structural S-series (S220GD up to S550GD) and is normally ordered with a zinc coating (+Z), zinc-aluminium-magnesium (+ZM) or zinc-iron alloy (+ZF) depending on the environment. Because of its high yield, S550GD suits load-bearing sections where a lower grade would need more material - the strength-per-weight advantage is exactly why it appears in heavy frames, racking and agricultural machinery.
2. Chemical Composition and Mechanical Data
The chemistry below is typical ladle analysis held within EN 10346 limits; mechanical values are those normally certified by the mill:
| <=0.12 | ||
| <=2.00 | ||
| <=0.50 | ||
| <=0.030 | ||
| <=0.025 | ||
| >=0.015 | ||
| 60–275 g/m² |
| Yield strength Rp0.2 | >=550 MPa (EN 10346 minimum) |
| 560–700 MPa class (verify exact range with the supplier against the current standard) | |
| Elongation A80 | >=12% class for t <= 3 mm (verify against the latest EN 10346 edition) |
| 180℃ without cracking per EN 10346 bending requirements |
Note: EN 10346 does not define impact-energy requirements for this grade; if a project demands impact testing, specify it separately (e.g., EN ISO 148-1) and agree the acceptance value in the order.
3. Temperature Behavior: Coating and Steel Core
Two different "temperature limits" apply to a galvanized product - one for the zinc coating, one for the steel - and both are engineering guidance rather than EN 10346 requirements:
zinc coatings behave well up to roughly 200–250 ℃. Above that range, oxidation of the zinc accelerates and the protective life shortens quickly; molten zinc is reached only near 419 ℃.
Short-term peaks: brief excursions up to about 300 ℃ are tolerable for the coating, but the zinc surface will darken and lose protection - never design a permanent installation above ~250 ℃.
above roughly 300 ℃ the mechanical properties of the steel substrate begin to degrade; S550GD's guaranteed values apply at room temperature.
structural steels generally keep their properties down to about -40 ℃, but for S550GD at very low service temperatures, verify ductility and impact behavior with the supplier before specifying, because the standard does not guarantee impact performance.
4. Recommended Applications
cold-formed structural frames, roof purlins and wall cladding where long spans need higher strength at lower gauge.
chassis brackets, body panels and frame components that need 550 MPa-class strength with corrosion protection.
tractor bodies, implement frames and silo components exposed to moisture and fertilizers.
cabinets and control boxes where flatness, strength and coated protection are all required.
ductwork and ventilation components that see condensation and mechanical handling.
5. Procurement Checklist
Order by standard: EN 10346, grade S550GD, coating system (+Z / +ZM / +ZF), coating class (e.g., Z275).
Confirm the required mechanical values (yield, tensile, elongation) with the supplier's current mill certificate; do not rely on generic tables.
If the service temperature exceeds 250 ℃ or falls below -40 ℃, discuss the application with the supplier before ordering.
Request certificates per EN 10204 (3.1) and independent third-party inspection if the project demands it.
Plan handling: high-strength grades show more springback in forming - confirm bend radii and tooling with the fabricator.
6. Frequently Asked Questions
As engineering guidance: continuous service up to roughly 200–250 ℃ for the zinc coating, short peaks near 300 ℃, and mechanical property guarantees at room temperature. These are not EN 10346 requirements.
Pure zinc melts at about 419 ℃, but long before that - above roughly 250 ℃ - oxidation accelerates and the coating loses its protective life. Design the service temperature well below that.
Structural steels generally behave well down to about -40 ℃, but EN 10346 does not guarantee impact performance for S550GD. For cold-climate structures, agree impact testing and acceptance values with the supplier.
DX51D is a commercial forming grade (yield typically <=360 MPa) for general bending; S550GD is a structural grade with minimum yield 550 MPa for load-bearing members. They are not interchangeable.
Yes, with its low carbon content it is weldable by conventional processes; control heat input to limit strength loss in the heat-affected zone, ventilate zinc fumes, and repair the coating at welds with zinc-rich paint.
For exposed structures use Z275 (≈275 g/m²) or a +ZM coating with equivalent cut-edge protection; match the class to the environment and design life rather than defaulting to the minimum.
Note: Rewritten version removes the fabricated impact-test requirement, flags and unifies tensile-strength conflicts, labels temperature figures as engineering guidance, and adds a structured FAQ with CTA buttons.
